Many companies are looking for workers for gold- those who have the skills to manufacture gold, to make it in the right condition, and to make chains.
So today, in this entire article, I will tell you what the jobs in the gold industry are and who does which job so that you can also apply.
To know what else is important in gold processing, click on our website Todayalljobs24.
There are many jobs in the gold business; you guys can do any job.
For example:
- Cleaning gold
- Getting gold cut
- Gold pairing
- Polishing gold
- Gold designing
- Setting pearls in gold
If you are looking for cleaning gold, getting gold, cutting gold, polishing gold, designing gold, setting pearls in gold if you want to know about them in detail, click on our website Todayalljobs24.
Cleaning Glod
To clean gold, first of all, we put the gold in a very hot furnace and do not take it out until the gold is completely melted.
After that, when it is completely melted, we take it out and press it lightly from two sides so that it becomes a little square. After that, we have to apply the acid.
After applying the acid, your gold will be completely clean, and you will know what grade your gold is.
To learn about the items used for cleaning gold, please click on our website Todayalljobs24.
Getting Gold Cut
We show the gold cutter a picture of the type of gold set we want to make, and we tell him that we have to make this set and that we have to make it in a certain weight, so we have to cut the pieces of this set accordingly.
After that, they put the gold in a rolling machine and take out a long piece. We check the weight of this piece, which we have said, and then they take out a piece of this weight and then calculate it.
They heat it and extract a die of the design they have to cut the gold set pieces.
Click on our website to learn about the things you need to keep in mind when cutting gold Todayalljobs24.
Gold Pairing
I worked as a goldsmith for three years. In goldsmithing, first we take the pieces that we have cut, then we check their weight.
After checking the weight, we attach a chain, then we join these pieces to it according to the type of set we want to make.
We design the set. After designing the set, we put plastic Paris on it. We use plastic Paris in a good way. We cover the seat, then let it dry for two minutes.
Then, after two minutes, we remove the seat from the wax and clean all the wax off it. After that, we place it on the cylinder to heat it so that it dries well. After it dries, we remove it from the cylinder.
Then we use KDM to join the set properly: take a little bit of gold, a little bit of dam, and melt it with a heat gun. When it melts well and mixes well with the ingredients, we press it from above.
After pressing it, we put it in a rolling machine. We take out a long piece of stone, heat it slightly, and cut it into a thin rod shape.
After that, we use KDM and a heat gun to join this set well. We join the pieces well with the chain so that it does not break.
Then, when we place the KDM inside the pieces of the set properly, we join it in every way. After joining, we check whether anything has been missed or whether any piece has been left behind.
After that, we pour a little water over the seat and remove it from the plastic bag. After removing it, heat the seat gently from all sides and put it in acid.
After that, we take some gold and melt it well. After melting it with a heat gun, we press it from the side. After that, we put it in a rolling machine and take out a long wire.
After heating this wire, we take out another thin, long wire from the rolling machine. After that, we fold this wire and heat it slightly.
After heating, we open the wire. After opening it, we straighten it and hit it lightly from above with a hammer.
After striking, we cut it slightly from the side and hit it with a hammer to make it round and make a thin tip from the front.
After that, we put it in a tool and thin the wire by pulling it from the front. And like that, we first pass it through the thick holes, and then we make it thinner until these rods reach the thorns.
Then we take out the rods. Then, after that, we make it thinner. Then we take out the hooks that are attached to the bottom of the seat.
When the wire becomes so thin, we roll it into a round shape and heat it slightly. Then we unroll it and wrap it around a needle. Then we heat it slightly and put it in acid.
After putting it in acid, we dry it, hold it with a pair of scissors, and cut it into equal sizes from the sides. Then we cut these ends into small pieces.
Place it on top of the iron and lightly hit it with a hammer from above. Then, hold it with a knife and press it from the side so that it closes and becomes round.
After rounding, they have to be grabbed one by one and joined under each piece of the set with the help of a heat gun.
After joining the joints, we heat the entire set well and dip it in acid, then take it out, heat it well, dip it in acid again, put it in water, take it out again, and dry it well. Weigh the set and give it to the polisher.
If you want to know more about gold pairing and get it here in detail, then click on our website Todayalljobs24.
Polishing Gold
Whatever set is to be polished is first put in a wire, covered well, and then put in a full bath of hot acid. After that, it is put in water.
If the color is fine, then it is fine. Otherwise, it is put in the acid once again and then put in water. Then it is washed well.
They dry it and put it in a polishing machine. After putting it in the polishing machine, they add lemon juice to it and turn off the machine.
Then, after 1 hour or 30 minutes, they take it out and put it in water to clean it and check its color. After that, they dry it well and tape it around the seat so that no pieces are left.
Then they put it in a matting machine to matt it. After matting, a final acid is applied to it. After applying the acid, they put it in water, and then they dry it well.
To learn more about what else is used to polish gold, click on our website Todayalljobs24.
After polishing, it shines very much. Then this set goes to the designer.
Table of Contents
Gold designing
First of all, we ask the set assembler how much it weighs and how much weight it should have. If he says that he wants to lose more weight, we design it by making it as deep as possible.
If he says that he wants to lose just a little weight, we design it from the very top, just as a shining, very light.
After figuring out everything, we bring the shine to it by designing, and different tools are used for designing.
We design the design on the pieces of the set with our own tools and give it a shine. We design the entire set with our own tools and give it a shine.
After giving it such a design and shine, we check the weight. If the weight is not right, we make it a little deeper and redesign it.
After this, we apply a light color to the set. We apply a light color to the shining pieces of the set. This enhances the beauty of the set.
After all this work is done, we give the set to be decorated so that they can decorate it nicely with beads, close it in a box, and give it to us.
If you want to know more about gold designing, click on our website Todayalljobs24.
Setting Pearls in Gold
If you want to know how to add pearls to gold and give it more beauty, then click on our website Todayalljobs24.
Before decorating the set, we thread the thread through the hooks at the top of the set so that the neck of the set is complete.
Then, we insert beautiful pearls into the hooks at the bottom to make it look beautiful and cute. Then, we insert pearls into the hooks.
Then we fit the jewels in wherever they are supposed to be, apply shiner to them, and then we pack the set in a nice box, close it, and give it to the person who made the set.
In this way, our set is finally complete, and we take our set to the jewelers and sell it to them, who then sell it at their own price.
How to make a set out of gold? If you want to know more about this, click on our website Todayalljobs24.
